-40%

802.11b/g WiFi Transceiver Board, RN-131C WiFly GSX

$ 2.64

Availability: 100 in stock
  • Condition: New
  • Brand: Unbranded/Generic
  • MPN: Does Not Apply
  • All returns accepted: Returns Accepted
  • Refund will be given as: Money Back
  • Item must be returned within: 14 Days
  • Return shipping will be paid by: Buyer

    Description

    802.11b/g WiFi Transceiver Board, RN-131C WiFly GSX
    WRL-10050
    This is a breakout board for the RN-131C WiFly GSX module, an ultra-low power 802.11b/g transceiver. This board breaks out all pins of the RN-131C to two 17-pin 0.1"-pitch headers. The board measures
    1.2" × 1.8"
    and comes fully assembled as pictured. The header pin rows are 1.1" apart.
    The Roving Networks RN-131C is a complete embedded TCP/IP solution. The combination of ultra-low power and the ability to wake up, connect to a wireless network, send data, and return to sleep mode in less than 100 milliseconds, allows the RN-131 to run for years on two standard AAA batteries. It uses only 35mA when awake and 4µA when asleep.
    The RN-131C incorporates a 2.4 GHz radio, processor, TCP/IP stack, real-time clock, crypto accelerator, power management, and analog sensor interfaces. This complete solution is pre-loaded with software to simplify integration and minimize development time for applications. In the simplest configuration, the hardware requires only four connections (PWR, TX, RX, GND) to create a wireless data connection.
    The RN-131C is rated for commercial temperature range, 0°C to +70°C).
    RN-131C WiFi Module Features
    Ultra-low power design for battery-powered applications
    Fixed transmit power: +18dBm
    Hardware interface: UART and SPI slave
    Supports Ad hoc and infrastructure networking modes
    User programmable GPIO & ADCs
    Real-time clock for time-stamping, auto-sleep, and auto-wakeup modes
    Runs directly from batteries (on-board battery boost circuit) or regulated power supply
    Configuration over serial or wireless interface using simple ASCII commands
    Over-the-air firmware upgrade
    Secure Wi-Fi authentication schemes (WEP / WPA / WPA2)
    Full on-board TCP/IP stack (no external drivers required)
    Specifications
    Networking Standards
    IEEE 802.11 b/g
    Data rates
    802.11b: 1, 2, 5.5, 11 Mbps
    802.11g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps
    Frequency Band
    2.412 - 2.484 GHz
    Modulation
    802.11b: DSSS (CCK-11, CCK-5.5, DQPSK-2, DBPSK-1)
    802.11g: OFDM
    Wi-Fi security
    WEP, WPA, WPA2
    Protocols
    DHCP, DNS, ARP, ICMP, FTP client, HTTP client, TCP, UDP
    Supply voltage
    3.3V ±10%
    Output power
    +18dBm
    Power consumption
    4µA sleep, 35mA active RX, 210mA TX
    Data rate
    464Kbps over UART, up to 1Mbps over SPI slave
    Range
    Up to 300 meters in open air
    Antenna options
    On-board chip antenna and U.FL connector
    Size
    1.49" × 0.78" × 0.15" (38 × 20 × 4 mm)
    Weight
    0.140 oz
    Certifications
    FCC, ICS, CE, Wi-Fi Alliance